Details of this Paper

Networking Assignment ? VERY URGENT !

Description

solution


Question

Need some one to do a Small Networking Assignment in few hours from now. Please check the details below and apply asap;Classful IP Addressing Scheme Project;;Scenario;In this project, you have been given the network address 192.168.9.0/24 to subnet and provide the Classful IP addressing for the network shown in the Topology Diagram (See Step 2 on page 2). The network has the following addressing requirements;The BRANCH1 LAN 1 will require 10 host IP addresses.;The BRANCH1 LAN 2 will require 10 host IP addresses.;The BRANCH2 LAN 1 will require 10 host IP addresses.;The BRANCH2 LAN 2 will require 10 host IP addresses.;The HQ LAN will require 20 host IP addresses.;The link from HQ to BRANCH1 will require an IP address for each end of the link.;The link from HQ to BRANCH2 will require an IP address for each end of the link.;(Note: Remember that the interfaces of network devices are also host IP addresses and are included in the above addressing requirements.);Task 1: Examine the Network Requirements.;Examine the network requirements and answer the questions below. Keep in mind that IP addresses will be needed for each of the LAN interfaces.;How many subnets are needed?;What is the maximum number of IP addresses that are needed for a single subnet?;How many IP addresses are needed for each of the branch LANs?;What is the total number of IP addresses that are needed?;Task 2: Design an IP Addressing Scheme.;Step 1: Subnet the 192.168.9.0 network into the appropriate number of subnets.;What will the subnet mask be for the subnetworks?;How many usable host IP addresses are there per subnet?;Fill in the following chart with the subnet information.;Subnet Number;Subnet Address;First Usable;Host Address;Last Usable;Host Address;Broadcast Address;0;1;2;3;4;5;6;7;Step 2: Assign the subnets to the network shown in the Topology Diagram below.;;When assigning the subnets, keep in mind that routing will need to occur to allow information to be sent throughout the network. The subnets will be assigned to the networks to allow for route summarization on each of the routers.;1.;Assign first subnet (lowest subnet) to the LAN connected to the Fa0/1 interface of BRANCH2. What is the subnet address?;2.;Assign second subnet to LAN connected to the Fa0/0 interface of BRANCH2. What is the subnet address?;3.;Assign third subnet to LAN connected to the Fa0/0 interface of BRANCH1. What is the subnet address?;4.;Assign fourth subnet to LAN connected to the Fa0/1 interface of BRANCH1. What is the subnet address?;5.;Assign fifth subnet to the WAN link from HQ to BRANCH1. What is the subnet address?;6.;Assign sixth subnet to the WAN link from HQ to BRANCH2.;7.;Assign seventh subnet to LAN connected to the Fa0/1 interface of HQ. What is the subnet address?;Note: The highest subnet will not be required in this topology.;Task 3: Assign IP Addresses to the Network Devices;Assign the appropriate addresses to the device interfaces. Document the addresses to be used in the Addressing Table provided under the Topology Diagram.;Step 1: Assign addresses to the HQ router.;1.;Assign the first valid host address in the HQ LAN subnet to the LAN interface.;2.;Assign the first valid host address in link from HQ to BRANCH1 subnet to the S0/0/0 interface.;3.;Assign the first valid host address in link from HQ to BRANCH2 subnet to the S0/0/1 interface.;Step 2: Assign addresses to the BRANCH1 router.;1.;Assign the first valid host address in the BRANCH1 LAN 1 subnet to the Fa0/0 LAN interface.;2.;Assign the first valid host address in the BRANCH1 LAN 2 subnet to the Fa0/1 LAN interface.;3.;Assign the last valid host address in link from HQ to BRANCH1 subnet to the WAN interface.;Step 3: Assign addresses to the BRANCH2 router.;1.;Assign the first valid host address in the BRANCH2 LAN 1 subnet to the Fa0/0 LAN interface.;2.;Assign the first valid host address in the BRANCH2 LAN 2 subnet to the Fa0/1 LAN interface.;3.;Assign the last valid host address in link from HQ to BRANCH2 subnet to the WAN interface.;Step 4: Assign addresses to the host PCs.;1.;Assign the last valid host address in the HQ LAN subnet to PC1.;2.;Assign the last valid host address in the BRANCH1 LAN 1 subnet to PC2.;3.;Assign the last valid host address in the BRANCH1 LAN 2 subnet to PC3.;4.;Assign the last valid host address in the BRANCH2 LAN 1 subnet to PC4.;5.;Assign the last valid host address in the BRANCH2 LAN 2 subnet to PC5.;Task 4: Test the Network Design.;Apply your addressing scheme to the Packet Tracer file that has been supplied with this lab. Check to see that all devices on directly connected networks can ping each other.;Addressing Table;Device;Interface;IP Address;Subnet Mask;Default Gateway;HQ;Fa0/1;N/A;S0/0/0;N/A;S0/0/1;N/A;BRANCH1;Fa0/0;N/A;Fa0/1;N/A;S0/0/0;N/A;BRANCH2;Fa0/0

 

Paper#72065 | Written in 18-Jul-2015

Price : $22
SiteLock