1. ATTENTION: DO NOT CONTACT ME IF YOU CANNOT PROVIDE AN ABSOULUTE, 100% GRAMMAR FREE, ERROR FREE, PEER REVIEWED REFERENCES, AT LEAST 3, AND MOST IMPORTANTLY, PLAGERISM FREE, ORIGINAL WORK!;2. THIS IS NOT A QUESTION / ANSWER FORMAT. THIS MUST BE DONE IN A PAPER FROM, (EXPLANATION OF EACH ANSWER) AT LEAST 5 DOUBLE SPACED, APA FORMATTED PAPER.;3. ONLY HIGHLY QUALIFIED ACCOUNTING DEGREED PROFESSIONALS PLEASE!;4. MOST IMPORTANTLY, PLEASE TAKE YOUR TIME, BUT FINISH ON TIME OR BEFORE TIME.;CASE 3A ? AUERBACH ENTERPRISES;Auerbach Enterprises manufactures air conditioners for automobiles and trucks manufactured throughout;North America. The company designs its products with flexibility to accommodate many makes and;models of automobiles and trucks. The company?s two main products are MaxiFlow and Alaska.;MaxiFlow uses a few complex fabricated parts, but these have been found easy to assemble and test.;On the other hand, Alaska uses many standard parts but has a complex assembly and testing process.;MaxiFlow requires direct materials costs which total $135 per unit, while Alaska?s direct materials;requirements total $110 per unit. Direct labor costs per unit are $75 for MaxiFlow and $95 for Alaska.;Auerbach Enterprises uses machine hours as the cost driver to assign overhead costs to the air;conditioners. The company has used a company-wide predetermined overhead rate in past years, but;the new controller, Bennie Leon, is considering the use of departmental overhead rates beginning with;the next year.;The following planning information is available for the next year for each the four manufacturing;departments within the company;Overhead Machine;Costs Hours;Radiator parts fabrication.............. $ 80,000 10,000;Radiator assembly, weld, and test.... 100,000 20,000;Compressor parts fabrication.......... 120,000 5,000;Compressor assembly and test........ 180,000 45,000;Total $480,000 80,000;Normally, the air conditioners are produced in batch sizes of 20 at a time. A production batch of 20 units;requires the following number of hours in each department;MaxiFlow Alaska;Radiator parts fabrication........... 28 16;Radiator assembly, weld, and test....... 30 74;Compressor parts fabrication......... 32 8;Compressor assembly and test......... 26 66;Total 116 164;Required;1. Compute the departmental overhead rates using machine hours as the cost driver.;2. Compute a company-wide overhead rate using machine hours as the cost driver.;3. Compute the overhead costs per batch of MaxiFlow and Alaska assuming;(a) The company-wide rate.;(b) The departmental rates.;4. Compute the total costs per unit of MaxiFlow and Alaska assuming;(a) The company-wide rate.;(b) The departmental rates.;5. Is one product affected more than the other by use of departmental rates rather than a company-wide;rate? Why or why not?;FURTHER INSTRUCTIONS;In this case, you are provided the overhead cost data for the Auerbach Enterprises. Management needs advice in determining how to allocate these costs utilizing a job order costing system either department-wide or company-wide. Address Questions 1through 5 located at the end of the case. Based on the case questions, you are required to provide a five PAGE double-spaced written report addressing management?s concerns and providing recommendations. The written report should be properly formatted according to APA guidelines and demonstrate research and critical thinking skills. Conclusions and recommendations should be supported by at least 2 scholarly sources from A Library or other external sources.;For Questions 1 through 4, you will need to complete several calculations. Be sure to label and clearly identify your work to demonstrate your understanding of the concept. The calculations should be included as part of your analysis and written recommendations required for submission.;For Question 5, fully address management?s concerns as part of your written analysis and recommendation using the new or the previous calculations to support your recommendation/explanation. The written analysis should be supported by at least 2 scholarly sources, excluding the textbook.;Week 2 Written Assignment should;Demonstrate graduate level work including appropriate research and critical thinking skills.;Be presented as a written analysis (not a question/answer format).;Incorporate case questions into the overall analysis.;Follow APA formatting guidelines including title page, reference page and in-text citations.;Consists of five double-spaced pages of content.;Provide at least 3 scholarly sources, excluding the textbook.
Paper#79324 | Written in 18-Jul-2015Price : $32